Headed Anchor Studs
Headed Anchor Studs
STUD SPECIFICATIONS
D
A
H
1/4
.187
.500
3/8
.281
.750
1/2
.281
1.000
5/8
.312
1.250
Description
Pounds
M Pieces
Part
Number
1/4 X 1 1/8
18
HA0250112
1/4 X 2 11/16
43
HA0250268
1/4 X 4 1/8
65
HA0250412
3/8 X 1 3/8
69
HA0370137
3/8 X 1 5/8
75
HA0370162
3/8 X 2 1/8
93
HA0370212
3/8 X 2 5/8
108
HA0370262
3/8 X 3 1/8
126
HA0370312
3/8 X 3 5/8
145
HA0370362
3/8 X 4 1/8
155
HA0370412
3/8 X 6 1/8
218
HA0370612


All S.W.F. headed anchors meet AWS specifications. Test reports available upon request.

HEADED ANCHOR STUDS are designed to be welded to flat surfaces or welding in the fillet or to the heel of angles. When ordering, specify if studs are to be welded to flat surfaces or in fillet or to heel of angle. All orders for studs include required ferrules.

LENGTH: Length is before weld. Stud diameters (D) 1/2" and below will be approximately 1/8" shorter after welding. 5/8" will be approximately 3/16" shorter after welding.

MATERIAL: Low carbon steel ASTM A108

STAINLESS STEELS: HA studs are also available in stainless steel

Online Quote Form
FERRULE SPECIFICATIONS
No.
D
B
F
M
FF-025
.454
.380
.234
.390
FF-037
.640
.505
.234
.390
FF-050
.795
.650
.250
.438
FF-062
1.030
.785
.328
.516
Description
Pounds
M Pieces
Part
Number
1/2 X 1 5/8
130
HA0500162
1/2 X 2 1/8
170
HA0500212
1/2 X 2 5/8
197
HA0500262
1/2 X 3 1/8
226
HA0500312
1/2 X 4 1/8
292
HA0500412
1/2 X 5 5/16
341
HA0500531
1/2 X 6 1/8
393
HA0500612
1/2 X 8 1/8
504
HA0500812
1/2 X 10 1/8
630
HA0501012
5/8 X 2 11/16
315
HA0620268
5/8 X 3 3/16
360
HA0620318
5/8 X 4 3/16
450
HA0620418
5/8 X 5 3/16
560
HA0620518
5/8 X 6 9/16
652
HA0620656
5/8 X 8 3/16
793
HA0620818
5/8 X 10 3/16
1039
HA0621018
Mechanical Property Requirements
 
Type A1
Type B2
Tensile Strength
55,000 psi min
(380 MPa)
60,000 psi min
(415 MPa)
Yield Strength
(0.2% offset)
__
50,000 psi min
(345 MPa)
Elongation
(% in 2-in.)
17% min
20% min
Reduction of Area
50% min
50% min
1 Type A studs shall be general purpose of any type and size used for purposes other than shear transfer in composite beam design and construction.
2 Type B studs shall be studs that are heated, bent, or of other configuration in 1/2 in (12.7 mm), 5/8 in (15.9 mm), 3/4 in (19 mm), 7/8 in (22.2 mm), and 1 in (25.4 mm) diameter that are used as an essential component in composite beam design and construction.